| Subject | Text |
| Jumpers to reset BIOS P/W on Toshiba satellite L755D-10V | Hi all,
this is my first post so i hope i've posted in the right place. My brother has a Toshib |
| Replacing busted DVD Player with a PC IDE, DVD ROM? | Hi all,
Does anyone have experience with replacing a bad DVD loader in a DVD player with an inexpe |
|
|
| Check F850 & F852. Replace the convergence ic's and solder up jumpers 010 and 050. |
| It seems that the DC protection is disconecting the outputs check if you hear a click about two seco |
| There around 1.8 ohms by memory don't forget the jumpers 010 and 050. Also going by memory. Any open |
| Technics sl pg 440 problem... | Hello, I have a problem finding the jumpers and resistors of an old cd sl pg 440 Technics. Not the 4 |
| According to the (now obsolete) IEC 750 standard, B is used to designate various sensors, transducer |
| I suspect both are surface mount jumpers. |
| transformer smokes | I am repairing a power supply for a scientific instrument. When I recieved it, it would not turn o |
| If you look there are 2 jumpers on the side right board on the left side of the board. These are not |
| I'm going by memory, Q410 0r 401 at the edge of the left board is your horizontal pulse. Resolder it |
| [quote:24543913f7="minnie"]The pip board is a plug in board to the main chassis. Look for a brown wi |
| problem still here | I did all this , i checked R7731 R7726 , R7711 , R7716 (giving 2.0ohms) and the i resoldered the 2 j |
| Child lock | You have been given the correct advice- there are n o jumpers, switches to change inside set- it is |
| Also I don't really have any tv repair experience but I do know how to solder pretty well. Is there |
| seagate hdd | Hello i have a seagate 160gb hdd and i am try to put it as a slave to my pc can anyone help how can |
| Denon DN-HD2500 Service Manual please? | Hi
Could anyone help with a copy of the service manual and/or schematics for Denon DN HD-2500 mid |
|
|
| Solder the jumpers on the signal board. IE the ones around L7711. Try that first. |
| Re: Radio BMW CM5905 | [quote:0a88038993="AdamBawaria"]Good day.
Can I ask for a BMW radio code?
no. serial K60548065F
T |
| ctc203ax pip bypass | Hi Guys anybody know how to bypass the pip board,i have here a rca 203ax chassis and the 18100 IC is |
| Look through thesev and see if a plausable match exists | JVC AV2000 N/A NO SOUND OR PICTURE - BUZZING SOUND FROM SWITCHING XFRM. - HIGH VOLTAGE BEINGS TO COM |
| Re: Same problem with KV-27S10 | I found the culprit on my KV-27S10... I saw tons of other common poblems on message boards but nothi |
| Thank you so much minnie! I downloaded a complete service manual for my tv so I found the fuses and |
| RE: Toshiba 50H71 No video or sound!! Please help! | Hello. After reading the post and the replies, it sounds like you have a few problems to overcome w |
| The pip board is a plug in board to the main chassis. Look for a brown wire going to it. You can jum |
| Did you check R7731/7726 1.8 ohm, R7711/7716 1.8 ohm, did you solder the 2 jumpers between the signa |
| Panasonic CT32G4 Child Lock permanently on | I have a Panasonic CT32G4 that somehow got child locked with a four digit unknown code in the " |
| Re: Blaupunkt San Francisco SQR28 Code Needed | [quote:8959b4f3e7="austinhermann"]I bought the car used and it doesn't have any mention of a code.
|
| I need schematic diagram of Sony ericsson t68i | power ways are cut off. i need it to trace and make jumpers for its positive ways. can you share p |
| protection good, now on to output | Thanks to Mitch & vtech for help with replacing the resistors. Now my reciever doesn't go into p |